Framing & Carpentry · Southwest & Southeast Florida
Framing & Carpentry Contractor in Southwest Florida
Code-compliant structural framing, roof trusses, light-gauge steel and finish carpentry for custom homes, additions, multifamily and commercial interiors, built square, plumb and ready for inspection.
Framing That Sets Up Every Trade That Follows
Framing is the skeleton of a building. Every wall, opening, beam and truss determines whether drywall goes up flat, cabinets hang level, windows seal properly and the roof carries Florida wind loads the way the engineer intended. DiBe Development and Construction provides framing and carpentry as part of our general contracting work on custom homes, additions, remodels, multifamily buildings and commercial interiors across Lee, Collier, Charlotte and the South Florida coast.
Because we manage the whole project, our framing is coordinated with the structural drawings, the truss package, the window and door schedule and the mechanical, plumbing and electrical rough-in. That coordination is what prevents the expensive problems owners see on poorly managed jobs: headers in the wrong place, ductwork that does not fit, missing blocking for cabinets and grab bars, and failed framing or wind-load inspections.
In Florida, framing is not only about holding the building up. It is also about holding it down. The Florida Building Code requires a continuous load path from the roof to the foundation, using straps, hurricane clips, hold-downs and anchor bolts sized for the design wind speed of the site. We build to the engineered drawings and prepare each stage for the inspector so the project keeps moving.
Framing & Carpentry Services We Provide
From the first wall plate to the last piece of trim, our framing and carpentry scope includes:
- Wood framing construction
- Metal stud framing
- Residential wall framing
- Commercial wall framing
- Interior partition framing
- Exterior wall framing
- Roof framing
- Floor framing
- Ceiling framing
- Door opening framing
- Window opening framing
- Stair framing
- Deck framing
- Porch framing
- Structural wood repairs
- Termite-damaged framing replacement
- Custom carpentry
- Finish carpentry
- Decorative woodwork installation
- Architectural trim carpentry
Wood Framing vs. Light-Gauge Steel Framing
Most single-family homes and additions in Southwest Florida combine masonry exterior walls with wood interior partitions and wood roof trusses, while many newer homes and multifamily buildings use wood frame exterior walls with engineered sheathing. Light-gauge steel studs are the standard for commercial interiors, tenant improvements and many multifamily corridors because they are noncombustible, straight and dimensionally consistent.
The right system depends on code, fire rating, budget and design. Wood framing is fast and familiar to every trade and accepts fasteners easily. Steel framing does not rot, warp or attract termites and is required in many commercial occupancies. We frame with both and can help you compare the options during preconstruction or through a consulting review.
When wood framing makes sense
Custom homes, additions, lanai and porch roofs, interior partitions in residential projects, and buildings where the design and code allow combustible construction.
When steel framing makes sense
Commercial build-outs, medical and office interiors, rated corridors and shafts, multifamily common areas and any space where the code or the owner requires noncombustible construction.
Roof Trusses and Florida Wind Loads
Engineered roof trusses are designed by the truss manufacturer for the specific roof geometry, spans and wind loads of your site. Installation matters as much as design. Trusses must be set at the specified spacing, braced temporarily during erection, permanently braced per the truss drawings, and connected to the walls with the specified hurricane connectors. Girder trusses, valley sets and hip systems all have their own connection requirements.
We review the truss package against the architectural and structural drawings before it is ordered, so bearing points, mechanical chases, attic access and ceiling heights are correct. During installation we verify layout, bracing and connectors so the framing and wind-load inspections pass the first time.
Opening Walls, Adding Beams and Remodel Framing
Many remodeling projects involve removing or relocating walls to create open kitchens, larger living spaces or new room layouts. Before a wall comes out we determine whether it is load bearing, what it supports, and whether plumbing, electrical or ductwork runs through it. Load-bearing walls require an engineered beam or header, properly sized posts and a path for the load down to the foundation, along with a permit.
In older Southwest Florida homes we often find framing that does not match modern code: undersized headers, missing straps, termite damage or prior unpermitted changes. We document those conditions, coordinate with the engineer when needed and correct them as part of the remodel, so the finished space is both open and sound.
Finish Carpentry and Interior Millwork
Finish carpentry is where a building starts to feel complete. Baseboards, casings, crown molding, door installation, stair parts, wainscoting, shiplap, coffered or beamed ceilings, closet systems and built-in shelving all depend on careful measurement and clean joinery. On custom homes and high-end remodels, finish carpentry is often the detail owners notice most.
On commercial projects, finish carpentry includes reception desks, wood wall panels, solid-surface and casework installation, door frames and hardware, and specialty ceilings. We coordinate these items with the millwork shop drawings, the finish schedule and the lighting plan so they arrive and install in the right sequence.
Framing Inspections and Quality Control
The framing inspection is one of the most important milestones in any permitted project. The inspector checks the structural members, connections, fire blocking, draft stopping, wall bracing, anchors and straps against the approved plans before the walls are closed in. On many projects there are separate inspections for roof sheathing nailing, wall sheathing, and wind-load connectors.
Before we call for inspection, our team walks the framing with the plans: checking stud spacing, header sizes, opening locations, blocking for cabinets, TVs, handrails, grab bars and wall-hung fixtures, and confirming every strap and clip is installed and fully nailed. That preparation is what keeps drywall, insulation and finish trades on schedule.
- Layout verified against plans
- Headers and beams sized per drawings
- Straps, clips and hold-downs fully fastened
- Fire blocking and draft stopping in place
- Blocking for cabinets, fixtures and accessories
- Openings sized for windows and doors
- Ready for MEP rough-in and inspection
Framing Costs and Schedule Factors
Framing cost depends on square footage, wall height, roof complexity, material type, number of openings, structural beams and the level of finish carpentry. Lumber and steel prices also change with the market, which is why we update framing numbers close to the purchase date and share supplier quotes with owners when it helps.
Schedule depends on truss lead times, inspections and weather. For additions and custom homes we order trusses early in the permitting process, stage materials to protect them from rain, and sequence framing so mechanical and electrical rough-in can follow immediately. Our project management and preconstruction services help keep framing from becoming the bottleneck.
Who We Serve
Homeowners
Wall removals, additions, lanai and porch roofs, built-ins and trim upgrades.
Custom home clients
Complete structural framing, trusses, sheathing and finish carpentry.
Developers and builders
Multifamily and townhome framing coordinated with the full construction schedule.
Commercial owners and tenants
Steel stud partitions, soffits, ceilings and casework for build-outs.
Our Process
01. Plan review
We review structural drawings, truss packages and openings before ordering.
02. Material takeoff
Accurate lumber, steel, truss and hardware quantities with current pricing.
03. Layout and framing
Walls, beams, trusses and sheathing installed per the approved plans.
04. Connectors and blocking
Straps, clips, hold-downs and blocking installed and verified.
05. Inspection
Framing and wind-load inspections scheduled and passed.
06. Finish carpentry
Trim, doors, millwork and built-ins installed after drywall and paint prep.
Consulting Before You Build
Not ready to start construction? DiBe Development & Construction also offers construction consulting: feasibility reviews, budgets, plan and bid reviews, schedules and owner’s representation. Many clients start with a consultation to understand scope, cost and risk before committing to a full project.
Related Services
Custom Home Builder
Full-service custom homes from foundation to finish.
Home Additions
Room additions, second stories and garage conversions.
Home Remodeling
Whole-home renovations and open-concept remodels.
Structural Concrete & Masonry
Foundations, block walls, tie beams and columns.
Tenant Improvements
Commercial interior build-outs with steel framing.
Interior Finishes
Drywall, ceilings, flooring, paint and trim.
See all construction services, our service areas and the full site map.
Service Areas
We provide framing and carpentry services throughout Southwest Florida, including Fort Myers, Cape Coral, Lehigh Acres, Naples, Estero and Bonita Springs, and Southeast Florida, including Miami, Fort Lauderdale and West Palm Beach.
Framing Materials Built for the Florida Climate
Heat, humidity, termites and hurricanes all shape how a Florida building should be framed. Lumber that sits in the rain before it is covered can swell, twist and grow mold, so we schedule deliveries close to installation, keep material off the ground and dry-in the structure as quickly as practical. Where wood contacts concrete or masonry, we use pressure-treated plates and the separation details the code requires.
Termite protection starts before framing. Most permitted projects in Southwest Florida require a soil pretreatment or an approved alternative, and some owners choose borate-treated framing for added protection. We coordinate those treatments and keep the documentation the inspector and future buyers will want to see.
Engineered lumber such as laminated veneer lumber, parallel strand lumber and I-joists is common in modern framing because it is straight, strong and available in long lengths. It allows wider openings and longer spans than dimensional lumber, which is why it shows up in open floor plans, large sliding glass door openings and lanai beams. Each engineered product has specific bearing, notching and fastening rules, and we install it according to the manufacturer and the structural drawings.
Wall Bracing, Sheathing and Shear Walls
Wind does not only lift a roof; it also pushes sideways on the walls. Wood-frame buildings resist those lateral forces through braced wall panels and shear walls, usually structural sheathing nailed to the studs in a specific pattern and connected to the foundation with hold-downs. The nail size, spacing and edge distance all matter, and inspectors check them before the walls are wrapped.
On the roof, sheathing nailing is just as important. Florida code calls for specific fastener schedules for roof decking, with tighter spacing in edge and corner zones where wind uplift is highest. We verify roof deck nailing before underlayment goes down, because once the roof is dried in, those fasteners can no longer be inspected.
Commercial Steel Stud Framing and Interior Systems
On commercial projects, framing is usually light-gauge steel studs and track forming partitions, demising walls, shaft walls, soffits and ceiling systems. Stud gauge, spacing and maximum height depend on the wall height and what the wall carries, such as tile, casework, wall-hung equipment or television mounts. Fire-rated walls must match a tested assembly, including stud size, board type, layers and fastener spacing, and penetrations must be firestopped with listed systems.
We coordinate steel framing with ceiling grids, sprinkler mains, ductwork and electrical so that soffits and bulkheads are framed where they are needed and access panels end up in usable locations. For medical, dental and office build-outs we add backing for equipment, grab bars, cabinetry and monitors before the walls close, which avoids costly retrofits after the space is finished. See our tenant improvements page for more on commercial interior construction.
Lanai, Porch and Outdoor Framing
Southwest Florida living happens outdoors, so many of our framing projects involve covered lanais, porches, pergolas, outdoor kitchens and screen enclosure roof structures. These elements are exposed to full wind loads and constant moisture, so connection hardware, beam sizing and material selection matter. We use treated or naturally durable materials where appropriate, stainless or hot-dip galvanized fasteners in coastal areas, and engineered connections where the covered roof ties into the existing house.
Tying a new roof into an existing home is a detail-heavy task: the existing roof framing must be evaluated, the new structure must be flashed and sealed to prevent leaks, and the drainage needs to work with gutters and grading. Our outdoor living team handles the whole package from framing through roofing, ceilings, lighting and finishes.
Finish Carpentry Details That Signal Quality
Small details separate average carpentry from excellent carpentry. Mitered corners should be tight and glued, nail holes filled and sanded, casings consistent around every opening, and baseboards scribed to uneven floors rather than leaving gaps. Doors should swing freely, latch cleanly and have even reveals. Stair treads should be level and quiet. These details depend on careful framing first; a straight, plumb wall makes clean trim possible.
For custom homes and high-end remodels we can build or install coffered ceilings, tongue-and-groove wood ceilings, beam wraps, paneled walls, window seats, mudroom lockers, entertainment walls, closet systems and pantry shelving. We coordinate wood species, profiles and paint or stain finishes with your designer and confirm everything with samples before installation.
- Coffered and beamed ceilings
- Wainscoting, board-and-batten and paneled walls
- Shiplap and tongue-and-groove accents
- Custom closets, pantries and mudroom built-ins
- Stair railings, balusters and newel posts
- Window seats and entertainment walls
Why Owners Choose DiBe for Framing and Carpentry
Framing contractors are easy to find; framing that is coordinated with the rest of the building is harder. As a licensed general contractor, DiBe Development and Construction manages framing as part of the full project, which means the person responsible for framing is also responsible for the schedule, the inspections, the trades that follow and the final result. There is no finger-pointing between the framer and the builder because they are the same team.
We also offer construction consulting for owners and developers who already have a framing bid or a set of drawings and want an experienced review of scope, pricing and constructability. Call (239) 414-3423 to talk with our team about your project in Fort Myers, Cape Coral, Naples, Lehigh Acres, Bonita Springs, Port Charlotte or along the South Florida coast.
Common Framing Problems We Fix
Some of our framing work begins after another contractor has left. We are regularly asked to correct framing that failed inspection, walls that are out of plumb, sagging headers, notched or drilled joists that weakened the structure, missing hurricane connectors and termite-damaged plates in older homes. Each of these problems has a correct repair, and some require an engineer’s letter before the inspector will accept them.
Our process is to document the condition with photos, identify the cause, propose a repair that meets code and the engineer’s direction, and complete it with the required inspection. For homeowners buying or renovating older properties, we can also evaluate visible framing during a pre-renovation walkthrough so surprises are found before the budget is set.
- Failed framing inspection corrections
- Out-of-plumb or bowed walls
- Sagging or undersized headers and beams
- Over-notched or over-drilled framing members
- Missing or incomplete hurricane straps and clips
- Termite or water-damaged plates and studs
Framing for Additions, Second Stories and Garage Conversions
Additions bring their own framing challenges because new work must meet current code while connecting to an existing structure that may have been built decades ago. Second-story additions require the existing walls and foundation to be evaluated for the new loads, often with an engineer’s analysis, and may need new posts, beams or footings. Room additions require the new roof to tie into the old one without creating leaks, low spots or ventilation problems.
Garage conversions usually involve framing in the garage door opening, raising or leveling the floor, adding insulation and interior walls, and making sure the new space meets egress, ventilation and energy code requirements. We handle the design coordination, permits and framing as one package through our home additions service, so the new space looks and performs like it was always part of the house.
Framing & Carpentry FAQs
Do you frame with wood or steel?
Both. We use wood framing for most residential work and light-gauge steel for commercial interiors and other spaces where the code or design calls for noncombustible construction.
Can you remove a load-bearing wall?
Yes, with an engineered beam or header, proper posts and a permit. We first confirm what the wall supports and what utilities run through it.
Do you install roof trusses?
Yes. We review the engineered truss package, install trusses with the required bracing and connect them with the specified hurricane connectors.
What is a continuous load path?
It is the chain of connections, from roof sheathing to trusses, walls, and foundation, that resists uplift and lateral wind forces. Florida code requires it, and inspectors check it at the framing stage.
Do you do finish carpentry and trim?
Yes. Baseboards, casings, crown molding, doors, built-ins, wood ceilings and custom millwork are part of our carpentry scope.
How long does framing take on an addition?
Many single-story additions are framed in a matter of days to a couple of weeks once the slab and walls are ready, depending on size, truss delivery and inspections.
Do you build lanai and porch roofs?
Yes. We frame covered lanais, porches and pergolas, tie them into the existing home with engineered connections, and complete the roofing, ceiling and electrical work.
Is termite treatment required before framing?
Most permitted new construction and additions in Florida require a soil treatment or an approved alternative. We coordinate it and keep the certificate for your records.
Do you frame fire-rated walls for commercial spaces?
Yes. We build rated partitions, demising walls and shaft walls to tested assemblies and coordinate listed firestopping for penetrations.
Can you review a framing bid I already have?
Yes. Our construction consulting service reviews framing scopes, quantities and pricing so you can compare bids with confidence.
What happens if framing fails inspection?
The inspector issues a list of corrections. We make the repairs, obtain any required engineering letters and schedule a re-inspection so the project can move to insulation and drywall.
Plan Your Framing or Carpentry Project
Tell us about your project and our team will follow up to discuss scope, budget and schedule.